Accessories



Isocheck PRIMO & PRIMO HL Isocheck ULTIMO Isocheck 32T Isocheck 37T Isocheck 27C, 23C & 14C Isocheck 28T, 24T & 15T Isocheck RENOVO Isocheck Deep Batten Isocheck Shallow Batten Isocheck Cradle Isocheck Barrier Mat 5 & 10 Isocheck Impact Mat 100, 200 & 300 Isocheck Re-Mat 3 & Re-Mat 5 Isocheck Re-Mat Base 3 & 6 Isocheck Re-Cork 3 & Re-Cork 5 Isocheck Screedcheck XL5 Isocheck Screedcheck XL8 Isocheck Screedcheck XL10 Isocheck Phonewell Isocheck Absorba ceiling & wall panels Isowave System 23 for Walls Isowave System 23 for Ceilings Accessories

0845 838 3399

Isocheck isolation strip

- for stud walls and steel & timber joists

Used to enhanced the impact sound transmission on stud
walls, steel and timber joists.

Commonly used for refurbishment upgrades, its adhesive backing ensures it can be held in position as the works progress.

Download the Isocheck Isolation Strip Data Sheet

Isocheck Expandastrip

- permanently elastic open cell polyurethane foam

Used for joints between precast units, sealing around doors and window frames, or between corrugated roofing panels, roof structures and roof lights ventilation and air conditioning ductwork.

Also used as a primary or secondary seal in vertical and horizontal joints of building facades as well as metal painted cladding systems, window perimeter curtain walling and skylights.

Download the Isocheck Expandastrip Data Sheet

Isocheck Re-Mat wall isolation strip

- for masonry walls

Isocheck Re-Mat Isolating Strips are designed to be installed beneath blockwork walls to isolate the wall from the concrete floor and reduce structure borne noise.

The Isolating Strips are composed of a rubber crumb which provides exceptional stability and minimal creep.

Download the Isocheck Re-Mat Wall Isolation Strip Data Sheet

Isocheck decoupling (resilient) bar

A concealed suspension section (metal channel) which serves to enhance the acoustic properties of a separating floor or wall when used in conjunction with other acoustic systems.

The bar decouples the Isocheck panel or standard high density plasterboard from a timber stud wall or joisted floor.

In the case of a medium depth separating floor the bar allows a lesser performing and costly floating floor to comply with the manditory acoustic test criteria specified in Approved Document E of the building regulations. It is easy to fix and when installed correctly is very affective in improving the structures acoustic performance.

Download the Isocheck Decoupling Bar Data Sheet


Isocheck perimeter flanking band

Isocheck flanking bands act as anti-noise gaskets between floating floor systems and structural elements.

In this way, expansion is also catered for without the need for an air gap, where noise leakage may otherwise occur.

Intumescent Acoustic FR Sealant

Isocheck acoustic fire rated sealant is used to reduce the
unwanted airborne sound that is commonly found to pass
around the junction between ceilings and walls.

Other common areas requiring attention are sealing around
service penetrations in the Isomass floating floor system.
Supplied in 310ml tubes.

Impacta Pads

Isocheck Impacta Pads are suitable for creating isolation of flanking noise elements, for example, where kitchen units are connected to walls. This common connection encourages impact/structure-borne sound transmission to travel from the units up/down the structural wall to the dwelling above/below.

Other suitable locations may be under bath feet, etc.

Isocheck Adhesive

For use with both Isocheck and Econocheck tongued & grooved board joints.

As a rule of thumb a 1 litre bottle (as illustrated) should cover approx 20m2 depending on the board size, ensuring glue is always applied to the top and bottom of the t&g joint.

Isocheck Acoustic Hangers

Many systems designed for use on timber or concrete separating floors benefit from decoupling the ceiling and increasing the airspace beneath the supporting floor.

Where the floor to ceiling height allows Acoustic Hangers often provide the best performance when installed with an acoustic floor treatment.

Mineral Fibre Insulation

All systems designed for use on timber new build or
conversion party floors will require mineral wool insulation
between the joists.

This is commonly no more than 100mm thick and around 45kg/m3.

It is available from most distributors/builders merchants. If in any doubt please contact us for a specification to suit your construction.

 

 





 

 

© 2006-2015 Isomass Ltd. | Terms & Conditions | Privacy Policy | Accessibility Statement

 

Designed by jpatl.com